纺织天平

克重仪套装（圆盘取样器+纺织天平）价格：1250元/套符合iso 3801,gb 4669,astm d3776,12646,bs 2471,din53854,iws tm13,bs en 12127,m&s p65/p65a等标准

圆盘取样器（单件价格420元/台）

1． 本仪器适用于切取各种毛纺、棉纺、化纤、针织等织物的圆形样品。

2． 取样面积： 100cm2 （取样直径：11.29cm.

使用方法:

      a:将待裁织物平铺在橡胶垫上， 将圆盘取样器放在织物上，拉出取样器上的锁紧装置，旋转约90 度，一手扶住外罩，一手握住波纹手轮，并施加一定压力，然后顺时针旋转波纹手轮（转角大于 90 度），即可将圆试样裁取。

      b:取样器使用后即锁紧装置，旋转至原位，使刀片不能外露，以免伤手和其他物品。

结构与调整：

      a：切刀刀片为双面刀片共有四片，为圆外接四等份均布，刀片可以更换，具体操作为：松开十字螺钉（每片上有四颗螺钉），取下刀片压板与取样刀片，换上新的刀片，压上刀片压板，注意使刀片口为顺时针切向，并使四片刀口处于同一平面，然后拧紧十字螺钉即可。

     b：仪器底部有直纹刻痕，用于固定试样，便于切割，防止试样打滑。

注意事项：

 a:本仪器刀片刀口锋利，使用中不得将手放在底部，以免损伤。

 b:仪器裁取试样应该在橡胶垫上进行，仪器不用时擦拭干净，放在仪器盒中，以免损伤。

 c:使用一段时间后如果刀片不锋利，按 4.1 条更换刀片即可，刀片为普通双面刮胡须刀片，市面有售。

                        纺织天平（单件价格850元/台）                  天平防风罩50元/件

天枰介绍

台湾技术，德国进口r&b传感器
天平精度：110g/0.01g 3.g/m2，oz/yd2，tex，ne，g单位转换，点数六功能。conforms to iso 3801,gb 4669,astm d3776,12646,bs 2471,din53854,iws tm13,bs en 12127,m&s p65/standard and so on p65a

the taiwan technology, germany imports the r&b sensor

1.sample burin effective sample area: 100mm2

2.balance precision: 110g/0.01g 3.g/m2, oz/yd2, tex, ne, the g unit transforms, points six functions

disc sample introduction

 1. this instrument is suitable in cutting takes each kind of fabric the and so on wool spinning, cotton spinning, chemical fiber, knitting circular sample.

2. samples area: 100cm2

3. application methods: 

3.1, will treat cuts the fabric even shop to fill up in the rubber, will place the disc sample on the fabric, will pull out sample on the locking installment, will revolve approximately 90, will support the shell, will grip the ripple handwheel, and will exert the certain pressure, then the clockwise rotation ripple handwheel (corner will be bigger than 90), then will cut the round test specimen takes.

3.2, after the sample use is the locking installment, revolves to the home position, enables the bit to appear externally, in order to avoid wound and other goods.

4. structures with adjust

   4.1, the cutter bit altogether have four pieces for the double-edged razor blade, meets four equal parts even cloths for the circle outside, the bit may replace, holds the achievement specifically: the pine operates the cross bolt (on each piece to have four bolts), takes down the bit clamp and the sample bit, exchanges the new bit, presses the bit clamp, the attention clockwise causes the bit mouth for to cut to, and causes four piece of cutting edges to be in the identical plane, then screws tight the cross bolt then.

   4.2, the instrument base has the straight burr scratch, uses in the fixed test specimen, is advantageous for cuts, prevented the test specimen slips.

5, matters needing attention:

 5.1, this instrument bit cutting edge is sharp, in the use does not have to place the hand the base, in order to avoid damages.

 5.2, the instrument cuts takes the test specimen to be supposed to fill up in the rubber carries on, the instrument does not use when cleans cleanly, places in the instrument box, in order to avoid damages.

 5.3, after uses period of time if the bit is not sharp, according to 4.1 replacements bits, the bit for is then ordinary two-sided blows the beard bit, the market condition has sells

本产品的品牌是国产，型号是0，测量精度是0.01，电源电压是220（V），外形尺寸是0（mm），重量是7（kg），用途是适用于切取各种毛纺、棉纺、化纤、针织等织物的圆形样品，加工定制是否